# Single, Double and Triple Font Kits

1. Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the [MK4 ](/products/kegging-equipment/series-x-or-user-guide/preparation-and-setup.md#kl07429-mk4-regulator-1)or [MK5](/products/kegging-equipment/series-x-or-user-guide/preparation-and-setup.md#kl30670-mk5-regulator) regulator
2. Feed this through the gas inlet into the kegerator. 
3. Cut an approximately 1m length of 5mm x 8mm EVABarrier gas line from the end
4. Cut this section into approx 2 x 50cm lengths
5. Push each length into the 8mm duotight Equal Tee Piece
6. Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for [commercial (brewery made)](/products/kegging-equipment/kegland-undercover-build-in-semi-integrated-kegerator-or-user-guide/setup/keg-types/guide-to-commercial-kegs-and-couplers.md) beer or for [homebrew](/products/kegging-equipment/kegland-undercover-build-in-semi-integrated-kegerator-or-user-guide/setup/keg-types/guide-to-homebrew-cornelius-kegs-and-disconnects.md)
7. Insert the remaining length of 5mm x 8mm EVABarrier (that is connected to the regulator) into the the Equal Tee

<figure><img src="/files/o1fEa1DyHYwTJKwfgqz7" alt=""><figcaption><p>Double Gas Line Configuration</p></figcaption></figure>

#### Triple Font

1. Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the [MK4 ](/products/kegging-equipment/series-x-or-user-guide/preparation-and-setup.md#kl07429-mk4-regulator-1)or [MK5](/products/kegging-equipment/series-x-or-user-guide/preparation-and-setup.md#kl30670-mk5-regulator) regulator
2. Feed this through the gas inlet into the kegerator.&#x20;
3. Cut an approximately 1.5m length of 5mm x 8mm EVABarrier gas line from the end
4. Cut this section into approx 3 x 50cm lengths
5. Push each length into the 8mm duotight Equal Tee Piece

   <figure><img src="/files/DbXx649WnnnxOjhSYGd0" alt=""><figcaption><p>Triple Gas Line Configuration</p></figcaption></figure>
6. Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for [commercial (brewery made)](/products/kegging-equipment/kegland-undercover-build-in-semi-integrated-kegerator-or-user-guide/setup/keg-types/guide-to-commercial-kegs-and-couplers.md) beer or for [homebrew](/products/kegging-equipment/kegland-undercover-build-in-semi-integrated-kegerator-or-user-guide/setup/keg-types/guide-to-homebrew-cornelius-kegs-and-disconnects.md)
7. Insert the remaining length of 5mm x 8mm EVABarrier (that is connected to the regulator) into the the Equal Tee

#### Quad Font

1. Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the [MK4 ](/products/kegging-equipment/series-x-or-user-guide/preparation-and-setup.md#kl07429-mk4-regulator-1)or [MK5](/products/kegging-equipment/series-x-or-user-guide/preparation-and-setup.md#kl30670-mk5-regulator) regulator
2. Feed this through the gas inlet into the kegerator.&#x20;
3. Cut an approximately 2m length of 5mm x 8mm EVABarrier gas line from the end
4. Cut this section into approx 4 x 50cm lengths
5. Push each length into the 8mm duotight Equal Tee Piece

   <figure><img src="/files/VuYEtloFtNLekqtGtuc5" alt=""><figcaption><p>Quadruple Gas Line Configuration</p></figcaption></figure>
6. Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for [commercial (brewery made)](/products/kegging-equipment/kegland-undercover-build-in-semi-integrated-kegerator-or-user-guide/setup/keg-types/guide-to-commercial-kegs-and-couplers.md) beer or for [homebrew](/products/kegging-equipment/kegland-undercover-build-in-semi-integrated-kegerator-or-user-guide/setup/keg-types/guide-to-homebrew-cornelius-kegs-and-disconnects.md)
7. Insert the remaining length of 5mm x 8mm EVABarrier (that is connected to the regulator) into the the Equal Tee


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://docs.kegland.com.au/products/kegging-equipment/kegland-undercover-build-in-semi-integrated-kegerator-or-user-guide/font-kit-assembly/single-double-and-triple-font-kits.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.