Preparation & Setup

Series 4 User Guide | Preparation & Setup

Installation & Setup

Preparation

Remove and check all items from inside the kegerator

Remove any protective film and tape from the kegerator

Inspect kegerator for any damage that may have incurred in transit including liquid or oil marks inside packaging. If any damage is noted contact your retailer

Castor Wheels Installation

Make sure the kegerator is empty

Carefully lay the kegerator on its side on a soft surface such as carpet, cardboard or a towel. NOTE: Ensure the kegerator is tipped onto the right hand side (as seen from the front). Tipping the kegerator towards the inlet side of the compressor will decrease the chance of oil migrating into refrigerant line which can cause cooling and noise issues

Unscrew the feet from the base of the kegerator

Remove the screws in the base of the kegerator in each corner. These are pre-installed screws that are used to mount the castor wheels. NOTE: These can be quite tight from the factory. A 5/16" socket or wrench will allow more leverage than a Philips driver if required

The two locking castor wheels should be installed towards the front of the kegerator

Position the kegerator back upright and leave for a minimum 1 hour before turning it on to allow the refrigerant gas to settle. If installing the castors shortly after receiving the kegerator, leave the kegerator upright for a minimum of 24 hours before turning it on

NOTE: The screw holes may be filled with foam and have a foil covering. If this is the case push and thread the screws through the foam or foil. The screw will then catch on the thread allowing it to be screwed in completely

Chrome Plated Guard Rail Installation

Position the guard rail so the feet line up with the holes in the top of the kegerator

Push the feet of the railing firmly into the holes

CO2 Cylinder Bracket Installation (optional)

Align the four holes in the bracket with the four studs on the back of the kegerator

Insert the studs into the holes and then push the bracket down firmly to secure it

Installing Regulator onto the CO2 Cylinder

KL07429 MK4 Regulator

Ensure the CO2 cylinder is off by turning the cylinder valve handle clockwise

Ensure the regulator dial is completely unscrewed and there is a nylon regulator washer between the type 30 nut and stem and the CO2 cylinder

Hand tighten the nut and stem onto the CO2 cylinder then tighten further with a 7 in 1 tool or a suitable wrench

KL30670 MK5 Regulator

Ensure the CO2 cylinder is off by turning the cylinder valve handle clockwise

Ensure the regulator dial is completely unscrewed and there is a nylon regulator washer between the type 30 nut and stem and the CO2 cylinder

Hand tighten the nut and stem onto the CO2 cylinder using the knurled grip. MK5 Regulators can be hand tightened due to the new spigot seal design that easily compresses

Attach 8mm EVABarrier gas line to the Regulator

KL07429 MK4 Regulator

The MK4 regulator comes as standard with a KL06880 8mm x FFL duotight fitting

Thread the KL06880 duotight fitting onto the regulator by hand, then tighten gently with a 7 in 1 tool or a suitable wrench. NOTE: DO not over tighten as this may cause the duotight fitting to split

Ensure the end of 8mm EVABarrier is free of burrs and is a clean, 90° cut

Push the line firmly into the KL06880 duotight fitting, ensuring it is inserted up to the line as marked on the fitting (approx. 22mm)

KL30670 MK5 Regulator

The MK5 regulator comes as standard with an 8mm duotight ball valve and integrated check valve

Ensure the end of 8mm EVABarrier is free of burrs and is a clean, 90° cut

Push the line firmly into the duotight fitting, ensuring it is inserted fully (approx.22mm)

Ensure the ball valve is opened before using the MK5 Regulator

Feed the 8mm EVABarrier gas line into the Kegerator

Unscrew one of the caps on the back of the Series X and feed the EVABarrier gas line through the hole

Setup Font, Taps and Beer line(s)

Please refer to the Font Assembly for a detailed guide on the different types of fonts

Connect gas & beer lines to coupler or disconnects

Please refer to the Keg Types guide for assembly instructions for the different types of beer and gas connections

Balance Beer Lines and Carbonation levels

Please refer to the Balancing Kegerator Lines & CO2 guide for details on getting the system balanced for a great pour