Single, Double and Triple Font Kits

Series X Plus User Guide | Single, Double and Triple Font Kits

Single, Double and Triple Tap Fonts

1. Remove the cap from the top of the font and ensure the font collar is present at the base of the font prior to attaching any duotight compatible short shanks

2. Feed the length of 4mmx8mm EVABarrier beer line through the tap hole on the front of the font and feed the 4mmx8mm EVABarrier beer line through the slimline nut and convex collet on the inside of the font. For a guide to getting the correct length for beer line refer to Balancing Lines & CO2 Pressure

3. Push a 6.5mm x 8mm reducer onto the back of the duotight compatible short shank. NOTE: duotight collets are colour coded to represent the appropriate EVABarrier tubing diameter. 6.35mm collets are green, 8mm are black and 9.5mm are blue

   

   Attach duotight reducer to short shank
4. Feed the tail and thread of the duotight compatible short shank through the tap hole and align the curvature of the shank and the concave collet with the curvature of the font

5. Push each length of beer line into the 6.5mm x 8mm reducer which is attached to a short shank

6. Tighten the slimline nut onto the thread of the duotight compatible short shank to secure the shank to the font tower.

7. Repeat for all other duotight compatible short shanks and beer lines

8. Feed the beer lines from the duotight compatible short shanks into the kegerator

9. Using the included M5 x 30mm bolts, mount the font onto the kegerator after feeding the lines through into the kegerator

10. Attach each EVABarrier beer line to a liquid ball lock disconnect or keg coupler

11. Hand-tighten the tap (sold separately) onto the duotight compatible short shank

12. Tighten the short shank collar onto the tap using a 7 in 1 tap wrench/spanner

Tightening Short Shank with 7 in 1 tool

EVABarrier Gas Line Setup (Single Font Kit only)

1. Double check that the EVABarrier gas line is securely connected to the MK4 or MK5 regulator
2. Feed this through the gas inlet into the kegerator. If desired, convert the gas post to a Ball Lock Disconnect fitting using this guide
3. Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for commercial (brewery made) beer or for homebrew

EVABarrier Gas Line Setup (Double, Triple or Quad Font Kit)

Double Font

1. Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the MK4 or MK5 regulator
2. Feed this through the gas inlet into the kegerator. If desired, convert the gas post to a Ball Lock Disconnect fitting using this guide
3. Cut an approximately 1m length of 5mm x 8mm EVABarrier gas line from the end

4. Cut this section into approx 2 x 50cm lengths

5. Push each length into the 8mm duotight Equal Tee Piece

6. Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for commercial (brewery made) beer or for homebrew
7. Insert the remaining length of 5mm x 8mm EVABarrier (that is connected to the regulator) into the the Equal Tee

Double Gas Line Configuration

Triple Font

1. Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the MK4 or MK5 regulator
2. Feed this through the gas inlet into the kegerator. If desired, convert the gas post to a Ball Lock Disconnect fitting using this guide
3. Cut an approximately 1.5m length of 5mm x 8mm EVABarrier gas line from the end

4. Cut this section into approx 3 x 50cm lengths

5. Push each length into the 8mm duotight Equal Tee Piece

   

   Triple Gas Line Configuration
6. Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for commercial (brewery made) beer or for homebrew
7. Insert the remaining length of 5mm x 8mm EVABarrier (that is connected to the regulator) into the the Equal Tee

Quad Font

1. Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the MK4 or MK5 regulator
2. Feed this through the gas inlet into the kegerator. If desired, convert the gas post to a Ball Lock Disconnect fitting using this guide
3. Cut an approximately 2m length of 5mm x 8mm EVABarrier gas line from the end

4. Cut this section into approx 4 x 50cm lengths

5. Push each length into the 8mm duotight Equal Tee Piece

   

   Quadruple Gas Line Configuration
6. Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for commercial (brewery made) beer or for homebrew
7. Insert the remaining length of 5mm x 8mm EVABarrier (that is connected to the regulator) into the the Equal Tee