Single, Double and Triple Font Kits
Series X User Guide | Single, Double & Triple Font Kit Assembly
Last updated
Series X User Guide | Single, Double & Triple Font Kit Assembly
Last updated
Remove the cap from the top of the font and ensure the font collar is present at the base of the font prior to attaching any duotight compatible short shanks
Feed the length of 4mmx8mm EVABarrier beer line through the tap hole on the front of the font and feed the 4mmx8mm EVABarrier beer line through the slimline nut and convex collet on the inside of the font. For a guide to getting the correct length for beer line refer to
Push a 6.5mm x 8mm reducer onto the back of the duotight compatible short shank. NOTE: duotight collets are colour coded to represent the appropriate EVABarrier tubing diameter. 6.35mm collets are green, 8mm are black and 9.5mm are blue
Feed the tail and thread of the duotight compatible short shank through the tap hole and align the curvature of the shank and the concave collet with the curvature of the font
Push each length of beer line into the 6.5mm x 8mm reducer which is attached to a short shank
Tighten the slimline nut onto the thread of the duotight compatible short shank to secure the shank to the font tower.
Repeat for all other duotight compatible short shanks and beer lines
Feed the beer lines from the duotight compatible short shanks into the kegerator
Using the included M5 x 30mm bolts, mount the font onto the kegerator after feeding the lines through into the kegerator
Attach each EVABarrier beer line to a or
Hand-tighten the tap (sold separately) onto the duotight compatible short shank
Tighten the short shank collar onto the tap using a 7 in 1 tap wrench/spanner
Cut an approximately 1m length of 5mm x 8mm EVABarrier gas line from the end
Cut this section into approx 2 x 50cm lengths
Push each length into the 8mm duotight Equal Tee Piece
Insert the remaining length of 5mm x 8mm EVABarrier (that is connected to the regulator) into the the Equal Tee
Cut an approximately 1.5m length of 5mm x 8mm EVABarrier gas line from the end
Cut this section into approx 3 x 50cm lengths
Push each length into the 8mm duotight Equal Tee Piece
Insert the remaining length of 5mm x 8mm EVABarrier (that is connected to the regulator) into the the Equal Tee
Cut an approximately 2m length of 5mm x 8mm EVABarrier gas line from the end
Cut this section into approx 4 x 50cm lengths
Push each length into the 8mm duotight Equal Tee Piece
Insert the remaining length of 5mm x 8mm EVABarrier (that is connected to the regulator) into the the Equal Tee
Double check that the EVABarrier gas line is securely connected to the or regulator
Feed this through the gas inlet into the kegerator. If desired, convert the gas post to a Ball Lock Disconnect fitting using
Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for beer or for
Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the or regulator
Feed this through the gas inlet into the kegerator. If desired, convert the gas post to a Ball Lock Disconnect fitting using
Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for beer or for
Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the or regulator
Feed this through the gas inlet into the kegerator. If desired, convert the gas post to a Ball Lock Disconnect fitting using
Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for beer or for
Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the or regulator
Feed this through the gas inlet into the kegerator. If desired, convert the gas post to a Ball Lock Disconnect fitting using
Connect the other end of the EVABarrier to the duotight fitting on the coupler or a Ball Lock Disconnect. The fitting will depend on the kegerator setup - whether it is for beer or for