KegLand Kegerators can be configured with different font and tap options.

Depending on the kegerator, you can have from 1 - 8 taps, or possibly more with the Grand Deluxe range.

Fonts and taps can also have different configurations - you may chose standard stainless NukaTaps, the black Stealth Bomber NukaTaps or possibly you need Flow Control NukaTaps (if serving highly carbonated beverages, for example)

Fonts can be a standard tower configuration, a tee bar or a super slim tee bar type.

All KegLand Font Kits (as opposed to Font Only) include beer and gas line, shanks and duotight connectors (where necessary), standard black tap handles for NukaTaps and all required beer and gas line, as well as tee pieces to split the gas line as needed. A 7 in 1 tool for easy font and shank assembly is also required. The exact inclusions depend on the type of font and number of taps - please refer to the product page for the font kit for details.

Please refer to the guide below for the selected font kit assembly

1. Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the or regulator

2. Feed this through the gas inlet into the kegerator.

3. Cut an approximately 1m length of 5mm x 8mm EVABarrier gas line from the end

Quadruple Tap Font Kits

1. Remove the cap from the top of the font and attach the font to the top of the kegerator using four metric M5 stainless steel screws. The mounting points can be found on the inside of the font and can be attached using a long screwdriver, bit extender or flexible drill bit

2. Feed the length of 4mmx8mm EVABarrier beer line through the tap hole on the front of the font and feed the 4mmx8mm EVABarrier beer line through the slimline nut and convex collet on the inside of the font. For a guide to getting the correct length for beer line refer to Balancing Lines & CO2 Pressure

3. Push a 6.5mm x 8mm reducer onto the back of the duotight compatible short shank. NOTE: duotight collets are colour coded to represent the appropriate EVABarrier tubing diameter. 6.35mm collets are green, 8mm are black and 9.5mm are blue
4. Feed the tail and thread of the duotight compatible short shank through the tap hole and align the curvature of the shank and the concave collet with the curvature of the font

5. Push each length of beer line into the 6.5mm x 8mm reducer which is attached to a short shank

6. Tighten the slimline nut onto the thread of the duotight compatible short shank to secure the shank to the font tower.

7. Repeat for all other duotight compatible short shanks and beer lines

8. Feed the beer lines from the duotight compatible short shanks into the kegerator

9. Attach each EVABarrier beer line to a or

10. Hand-tighten the tap (sold separately) onto the duotight compatible short shank

11. Tighten the short shank collar onto the tap using a 7 in 1 tap wrench/spanner
12. NOTE: It is easiest to attach the shanks in the order below:

1. Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the or regulator

2. Feed this through the gas inlet into the kegerator.

3. Cut an approximately 2m length of 5mm x 8mm EVABarrier gas line from the end

4. Cut this section into approx 4 x 50cm lengths

Tee Bar Fonts

1. Remove the caps from the end of the fonts and ensure the font collar is present at the base of the font prior to attaching any duotight compatible short shanks

2. NOTE: Install shanks from the middle of the font outwards

3. Feed the length of 4mmx8mm EVABarrier beer line through the tap hole on the front of the font and feed the 4mmx8mm EVABarrier beer line through the slimline nut and convex collet on the inside of the font. For a guide to getting the correct length for beer line refer to Balancing Lines & CO2 Pressure

4. Push a 6.5mm x 8mm reducer onto the back of the duotight compatible short shank. NOTE: duotight collets are colour coded to represent the appropriate EVABarrier tubing diameter. 6.35mm collets are green, 8mm are black and 9.5mm are blue
5. Feed the tail and thread of the duotight compatible short shank through the tap hole and align the curvature of the shank and the concave collet with the curvature of the font. Angling the shank off to the side slightly is generally easiest

6. Push each length of beer line into the 6.5mm x 8mm reducer which is attached to a short shank

7. Tighten the slimline nut onto the thread of the duotight compatible short shank to secure the shank to the font tower.

8. Repeat for all other duotight compatible short shanks and beer lines

9. Feed the beer lines from the duotight compatible short shanks into the kegerator

10. Using the included M5 x 30mm bolts, mount the font onto the kegerator after feeding the lines through into the kegerator

11. Attach each EVABarrier beer line to a or

12. Hand-tighten the tap (sold separately) onto the duotight compatible short shank

13. Tighten the short shank collar onto the tap using a 7 in 1 tap wrench/spanner

1. Double check that the the 5mm x 8mm EVABarrier gas line is securely connected to the or regulator

2. Feed this through the gas inlet into the kegerator.

3. Cut an approximately 2m length of 5mm x 8mm EVABarrier gas line from the end

4. Cut this section into approx 4 x 50cm lengths