Setup

KegLand Undercover / Build In / Semi-Integrated Kegerator | Setup

Setup

Please refer to this video for a detailed guide to setting up a kegerator. This is for a Series X kegerator, but the specifics of font setup, balancing beer lines etc are exactly the same across kegerator models.

https://youtu.be/weO0rwg4ps4youtu.be

1

Preparation

• Remove all items from inside kegerator

• Ensure all items have been included

• Remove any protective plastic from the kegerator before first use

• Check for any damage which has occurred during transit including any liquid or oil marks on the inside of the packaging

2

Installing MK4 Regulator onto CO2 Cylinder

• Ensure the CO2 cylinder is off by turning the cylinder valve handle clockwise

• Ensure the regulator dial is completely unscrewed and ensure there is a nylon regulator washer between the type 30 nut and stem and the CO2 cylinder

• Hand tighten the nut and stem onto the CO2 cylinder then tighten further with a 7 in 1 faucet tap wrench/spanner

3

Attach EVABarrier to the regulator

• The Mk4 regulator provided in a Series X fridge comes as standard with an 8mm x FFL duotight Fitting (KL06880)

• Make sure the end of the EVABarrier hose doesn’t have any burrs and is cut straight and cleanly. Push the EVABarrier hose line firmly into the duotight fitting on the regulator and ensure it is secure up to the line indicated on the 8mm x FFL duotight fitting

• The gas tubing can then be fed through one of the two holes (remove threaded cap first) positioned on the left and the right at the back of the UnderCover Kegerator. The gas line will also need to be tee'd off if you have two or more taps (duotight tee pieces included with Font Kit)

Assembling Font Kits

Single, Double and Triple Tap Fonts

1. Remove the cap from the top of the font and ensure the font collar is present at the base of the font prior to attaching any duotight compatible short shanks

2. Feed the length of beer line through the tap hole on the front of the font and feed the beer line through the slimline nut and convex collet on the inside of the font

3. Push a 6.5mm x 8mm reducer onto the back of the duotight compatible short shank

4. Feed the tail and thread of the duotight compatible short shank through the tap hole and align the curvature of the shank and the concave collet with the curvature of the font

5. Push each length of beer line into a 6.5mm x 8mm reducer which is attached to a short shank

6. Tighten the slimline nut onto the thread of the duotight compatible short shank to secure the shank to the font tower

7. Repeat for all other duotight compatible short shanks and beer lines

8. Feed the beer lines from the duotight compatible short shanks into the kegerator

9. Attach the font to the top of the kegerator by screwing the font onto the font mounting points using four metric M5 stainless steel screws.

10. Attach each EVABarrier beer line to a liquid ball lock disconnect or keg coupler

11. Hand-tighten the tap (sold separately) onto the duotight compatible short shank

12. Tighten the short shank collar onto the tap using a 7 in 1 tap wrench/spanner

TIghtening Short Shank

Quadruple Tap Font

1. First, attach the font to the top of the kegerator using four metric M5 stainless steel screws. The mounting points can be found on the inside of the font and can be attached using a long screwdriver or flexible drill bit

2. Then attach the duotight compatible short shanks, duotight 6.5mm x 8mm reducer and beer line to the font tower as described in step 11. It is easiest to attach the shanks to the font tower in the order shown

3. Feed the beer lines from the duotight compatible short shanks into the kegerator.

4. Attach each EVABarrier beer line to a ball lock disconnect or keg coupler

5. Hand-tighten the tap (sold separately) onto the duotight compatible short shank

6. Tighten the short shank collar onto the tap using a 7 in 1 tap wrench/spanner