Operation

Display Panel Legend

1. Power Button

2. SET Button

3. Up and Down Buttons

4. Defrost Cycle Indicator

5. Fan Indicator

6. Celsius/Fahrenheit Button

7. Manual LED Button

Adjusting the Set Point Temperature

To adjust the Set Point Temperature:

1. Press the SET button to display the current Set Point Temperature.

2. Press the Up or Down buttons to modify and save the Set Point Temperature

3. Press the SET button to exit the Adjustment Status and display the current actual temperature

Change Display between Celsius and Fahrenheit

To change the displayed temperature between Celsius and Fahrenheit press the °C/°F button. Press it again to revert to the previous units.

Manually operate the internal LED

The internal LED is automatically turned on when the door is opened. It can be manually operated - turned on or off - using the Light Button. The LED is on a timer so it will automatically turn off after 2 minutes.

Enter Manual Defrost

The KegLand Undercover / Build In / Semi-Integrated Kegerator has a defrost cycle programmed in. Should you wish to perform a manual defrost for any reason (such as visible ice build up) this can be performed by pressing the Up button for 6 seconds to begin a defrost cycle. If a defrost cycle is running, performing this operation will manually stop the defrost cycle.

Adjust Hysteresis

Hysteresis is the allowed differntial from the Set Point Temperature before the compressor (cooling) operates. Thus, if the Set Point Temperature is 2°C and the Hysteresis is 3°C then the compressor will operate when the internal temperature reads 5°C, and it will continue to operate until the Set Point Temperature of 2°C is reached. The default hysteresis is 3°C, which is appropriate for most circumstances.

Note: Decreasing the hysteresis can increase power consumption

To Adjust the Hysteresis

1. Press the SET button and hold for 8 seconds to enter the parameter setup mode - L1 will flash on the display

2. Press the SET button to cycle through Parameters until L3 is displayed

3. Press the Up or Down buttons to modify the Hysteresis

4. Once the desired value is displayed it will be saved after the display stops flashing (approx. 6 seconds)

Temperature Calibration

If there is a large variance between the displayed temperature (IE the temperature of the internal temperature probe and the actual internal temperature of the kegerator (as measureed by a calibrated thermometer) then the Temperature Offset can be adjusted from -20°C to 20°C

A Temperature Offset will offset the displayed temperature by the entered amount.

Thus, if the displayed temperature is 2°C but the actual internal temperature is 4°C, and offset of +2°C is required.

Note: In most cases this is not necessary to be adjusted. There will be minor temperature differences in the kegerator due to airflow etc.

To Adjust the Offset

1. Press the SET button and hold for 8 seconds to enter the parameter setup mode - L1 will flash on the display

2. Press the SET button to cycle through Parameters until L5 is displayed

3. Press the Up or Down buttons to modify the Temperature Offset (from 20°C to -20°C)

4. Once the desired value is displayed it will be saved after the display stops flashing (approx. 6 seconds)

To Adjust the Defrost Duration

1. Press the SET button and hold for 8 seconds to enter the parameter setup mode - L1 will flash on the display

2. Press the SET button to cycle through Parameters until F1 is displayed

3. Press the Up or Down buttons to modify the Defrost Duration (from 1 minute to 60 minutes). The default setting is 30 minutes

4. Once the desired value is displayed it will be saved after the display stops flashing (approx. 6 seconds)

To Adjust the Defrost Interval Time

1. Press the SET button and hold for 8 seconds to enter the parameter setup mode - L1 will flash on the display

2. Press the SET button to cycle through Parameters until F2 is displayed

3. Press the Up or Down buttons to modify the Defrost Interval Time (from 00 hours to 24 hours). The default setting is 4 hours

4. Once the desired value is displayed it will be saved after the display stops flashing (approx. 6 seconds)

Factory Reset

To reset all settings (Set Point, Hysteresis, Offset etc) to factory defaults, press and hold the Up or Down buttons simultaneously for 8 seconds until the display flashes 888, then release. This will restore the unit to factory defaults.